You can use the default server and the same key used in step 5. Create a Radius server for clients. If you have a Dynamic WAN please note that this address can change, possibly breaking VPN connections. Specify the WAN address you want to use. Create a Pre-shared Secret Key for clients. Select the Remote Access VPN type (L2TP is recommended).
Port For Remote Access Mac Is OnMake a note of the address after. This chapter discusses the following topics:If you mac is on a wired connection that should be en0. That is, the traffic between the controller and AP is encrypted.Remote AP operations are supported on all of Aruba’s APs. Since the Internet is involved, data traffic between the controllerand the remote AP is VPN encapsulated.This remote computer is connected to an AirPort Extreme, which I’ll refer to as the router, and has a static internal IP address of 192.168.1.10.The local computer I’ll be using to connect to the remote computer is a MacBook.“Configuring the Secure Remote Access Point Service”Be cautious if you receive unsolicited requests to access your computer. The computer I’ll be connecting to remotely is an iMac, which I’ll call the remote computer, on my home network. Configuring the Router for Port Forwarding. Version 1 also included simple file transfer. It also allowed remote computers to be restarted or shutdown, to have their screens locked or unlocked, or be put to sleep or awakened, all remotely. Report abuse.The original release, which used the User Datagram Protocol (UDP) on port 3283, allowed remote computers (running Mac OS 8.1 or later) to be observed or controlled from a computer running macOS. Remote users can use the same features as corporate office users. Secure Remote Access Point Service extends the corporate office to the remote site. AP control and 802.11 data traffic are carried through this tunnel. 01Run describe-security-groups command (OSX/Linux/UNIX) using the.“Deploying a Branch Office/Home Office Solution”Remote APs connect to a controllerusing Extended Authentication and Internet Protocol Security (XAuth/IPSec). The licenses are cumulative each additional license installed increases the maximum number of APs supported by the controller.Configure the VPN server on the controller. There are several AP licenses available that support different maximum numbers of APs. (Aruba recommends this deployment when AP-to-controllercommunications on a private network need to be secured.) In this scenario, the remote AP uses the controller’s IP address on the private network to establish the IPSec VPN tunnel.Figure 24 Remote AP with a Private NetworkRemote AP in a Multi-Controller EnvironmentConfiguring the Secure Remote Access Point ServiceThe tasks for configuring an Aruba Access Points as a Secure Remote Access Point Service are:Configure a public IP address for the controller.You must install one or more AP licenses in the controller. The tunnel termination point used by the remote AP depends upon the AP deployment, as shown in the following scenarios:Deployment Scenario 1: The remote AP and controllerreside in a private network which is used to secure AP-to-controller communication. Once the VPN tunnel is established, the AP bootstraps and becomes operational. In this case, both the AP and controllerare in the company’s private address space.The remote AP must be configured with the IPSec VPN tunnel termination point. The following procedure describes how to create a DMZ address on the controller.1. This can be either a routable IP address that you configure on the controller, or the address of an external router or firewall that forwards traffic to the controller. For information on remote AP modes of operation, refer to “Advanced Configuration Options”Configure a Public IP Address for the ControllerThe remote AP requires an IP address to which it can connect in order to establish a VPN tunnel to the controller. The information in this section assumes the default mode of operation. This mode enables the virtual AP when the remote AP connects to the controller. By default, the remote AP operates in standard mode. Click Edit for the VLAN you just created.8. Navigate to the Configuration >Network > IP page.7. Select the port that belongs to this VLAN.6. Navigate to the Configuration >Advanced Services >VPN Services > IPSec page.3. The remote AP will be a VPN client that connects to the VPN server on the controller.1. For more details, see Chapter 14, “Virtual Private Networks”. On the NAT device, you must enable NAT-T (UDP port 4500 only) and forward all packets to the public address of the NAT device on UDP port 4500 to the controllerto ensure that the remote AP boots successfully.This section describes how to configure the IPSec VPN server on the controller. When both the controllerand the AP are behind NAT devices, configure the AP to use the NAT device’s public address as its master address. Click Done to return to the IPSec page.Once the remote AP is authenticated for the VPN and established a IPSec connection, it is assigned a role. To configure an Internet Security Association and Key Management Protocol (ISAKMP) encrypted subnet and preshared key, click Addin the IKE Shared Secretssection and configure the preshared key. Configure the L2TP pool from which the APs will be assigned addresses, then click Done.The size of the pool should correspond to the maximum number of APs that the controller is licensed to manage.5. To configure the L2TP IP pool, click Add in the Address Poolssection. ![]() For Service, select service, then select svc-ftp.B. For Service, select service, then select svc-tftp.D. For Destination, select alias, then select mswitch.D. For Service, select service, then select svc-l2tp.C. For Service, select service, then select svc-gre.D. This username and password must be validated by an authentication server before the remote AP is allowed to establish a VPN tunnel to the controller. When you provision the remote AP, you configure IPSec settings for the AP, including the username and password. In the Choose from Configured Policies menu, select the policy you just created.Before you enable VPN authentication, you must configure the authentication server(s) and server group that the controllerwill use to validate the remote AP. You must install the PEFNG and PEFV license, as described in Chapter 31, “Software Licenses”.5. For Default Role, enter the user role you created previously (for example, RemoteAP).User roles and policies require the PEFNG and PEFV license. In the Profiles list, select the VPN Authentication Profile> default-rap.3. Navigate to the Configuration >Security >Authentication > L3 Authentication page.2. Hap codec download for macConfigure the VPN server on the controller.4. Configure a public IP address for the controller.2. To configure the internal database for a remote AP user, do the following:1. Select the server group from the drop-down menu.Configuring Internal Database for AuthenticationYou can use the controller’s internal database as an authentication server.
0 Comments
Leave a Reply. |
AuthorLori ArchivesCategories |